陶瓷基复合材料注凝成型系统设计(含CAD零件图装配图)

资料介绍:
陶瓷基复合材料注凝成型系统设计(含CAD零件图装配图)(任务书,开题报告,外文翻译,论文说明书10000字,CAD图9张)
摘 要
现代工业的快速发展极快加大了人们对高性能陶瓷的需求。然而传统的陶瓷成型方法难以适应对材料品性日益提高的要求。注凝成型的出现,由于其成型坯体均匀性好、强度高,适应性强等优点,可适合成型从单组分陶瓷材料到复合陶瓷材料,从致密体陶瓷材料到多孔陶瓷材料及从简单形状到杂形状特异制品,给陶瓷成型工艺带来了一场革命 。本论文首先介绍了注凝成型技术的发展历史和目前国内外的发展现状,并对其成型原理与成型条件做了简要的说明;其次以氧化铝陶瓷复合材料为计算范本对陶瓷基注凝成型设备的总体结构(包括搅拌器、成型器和真空系统的构成)和各组成零件做了详细的设计与选型,并用CAD软件绘制出其总装图和部分零件图;其中在以500ml模拟溶液作为计算参考,设计特定的搅拌方式及搅拌模组。在成型器的设计上,为了保证坯体成型的完善度,加入了PLC的设计,以求达到温度的精准控制。并针对物料流动性差及特殊成型条件要求的特点,加入了真空系统的设计,以求更加完善的达到实验效果。
本注凝成型系统的设计所用原理基本来自机械工程本科教学内容。
[资料来源:http://www.doc163.com]
关键词:陶瓷基复合材料 注凝成型 PLC 搅拌 真空系统 CAD
The Design of CMC Gel-casting Equipment System
Abstract
The development of modern industry has rapidly increased the demand for high performance ceramics. However, the traditional method of ceramic molding tech is difficult to adapt to the increasing requirement on quality of materials. The appearance of gel-casting forming has full
With the blank. Because of its good uniformity, high strength, strong adaptability etc., can be suitable for forming ceramic material from one group to the composite ceramic material, ceramic material from dense to porous ceramic material and from simple to complex shape specific products, which has resulted in a revolution in ceramics molding process. This paper firstly introduced the history of gel-casting technology development and the development status at home and abroad, and telling the principle of forming and molding conditions briefly. Secondly designed the equipment by amusing alumina ceramic composite materials as the calculation model of ceramic matrix gel casting equipment (including mixer, a forming device and vacuum system ) and introduced the selection of detailed, then drew the assembly diagram and parts diagram by CAD software. IN the simulations with 500ml solution as the reference of calculation, designed the mixing module for stirring specific. In the design of the forming device, in order to ensure the forming processed perfectly, adding the PLC module, which in aim to achieve precise control of temperature. And according to the characteristics of the material fluidity and special molding requirements, the design has joined the vacuum system , in order to achieve the better experimental effect.
[来源:http://www.doc163.com]
The designs of the gel-casting system are based on principle from knowledge of the mechanical engineering undergraduate-teaching.
Keywords: CMC; gel-casting; PLC; stirring; vacuum system; CAD
整体结构设计及工作流程
设备结构及其工作流程陶瓷基复合材料成型设备的结构简图如图 1所示, 整台设备由搅拌器、成型器、机架三部分组成。搅拌器为低压容器, 形状为圆筒状, 侧面开有观察窗,侧壁上连接有进料管负责物料输入 (上有进料阀 )、进水管负责溶剂及催化剂等进入(上有进水阀 )、真空管负责制造低压环境(上有真空阀 )及底部阀门负责阻断搅拌器与成型器之间的连接。搅拌器底部的叶片通过电动机带动旋转。成型器为长方体, 顶盖上开有观察窗, 侧壁上连接有进料管 (上有三通阀 )、出水管 (上有出水阀 )、真空管 (上有真空阀 ), 在底部则放有加热体进行物料的加热成型。机架部分是由45钢材制成, 达到支承作用。
[资料来源:http://doc163.com]





[资料来源:www.doc163.com]
目录
摘 要 I
Abstract II
目录 III
第一章 绪论 1
1.1前言 1
1.2陶瓷基复合材料的注凝成型原理 1
1.3陶瓷基复合材料的发展及方向 2
1.4本文研究内容及意义 3
第二章 设备整体结构设计及工作流程 4
2.1整体结构设计及工作流程 4
2.3工况要求 5
第三章 搅拌器的设计 6
3.1缸体设计 8
3.2搅拌器选型 9
3.3传动装置选型 11
第四章 成型器设计 12
4.1加热系统设计 13
4.3声光报警电路 14
4.4人机界面 14
4.5 系统软件的设计 15
4.5.1 系统的主程序 15
4.5.2 系统的控制程序 15
第五章 真空系统的设计 17 [资料来源:Doc163.com]
5.1真空系统组成 17
第六章 总结 19
参考文献 21
致谢 23
[来源:http://Doc163.com]
上一篇:MQ2533四连杆门座起重机起升机构设计(含CAD图,SolidWorks三维图)
下一篇:没有了
