Open Nav

基于PWM调速技术的智能温控风扇设计

以下是资料介绍,如需要完整的请充值下载.
1.无需注册登录,支付后按照提示操作即可获取该资料.
2.资料以网页介绍的为准,下载后不会有水印.仅供学习参考之用.
   帮助中心
资料介绍:

基于PWM调速技术的智能温控风扇设计(任务书,开题报告,论文11900字)
摘要
对于本次基于PWM技术的智能温控风扇设计,首先通过键盘确定温度,接着使用三个按键设置27摄氏度为下限值,30摄氏度为上限制,设置方法也可以用遥控操作,当DS18B20感应温度的值低于下限值则风扇不转动,当温度在所设的温度之间时扇叶缓慢转动,当温度超出所设的最高值时,风扇高速旋转。另外本设计采用数码管,经温度传感器DS18B20将相关温度信息传送给单片机,最后通过数码管显示出来。本设计还可用红外遥控控制,操作简便。此外,风扇还设定了三个固定档位,低速,中速,高速档位,使用方便。
关键词:温度传感器DS18B20 智能控制 红外遥控

Abstract
For this time based on PWM technology, intelligent temperature control fan design, first through the keyboard to determine the temperature, then use the three keys to set the 27 degrees Celsius for the lower limit, 30 degrees Celsius for the upper limit, the setting method can also be used remote operation, when the DS18B20 induction temperature The fan is not rotating, and when the temperature is between the set temperature, the fan rotates slowly, and when the temperature exceeds the set maximum value, the fan rotates at high speed. In addition, the design of the use of digital control, the temperature sensor DS18B20 will be related to the temperature information sent to the micro-controller, and finally through the digital display. the method can also be set up by remote control when the value of the temperature sensor below the lower limit of the fan is not operating.After the power-down can still save the last set value, stable performance, accurate control. [资料来源:Doc163.com]
Key Words:Temperature SensorDS18B20;intelligent control;Infrared remote control.
 

[来源:http://www.doc163.com]

基于PWM调速技术的智能温控风扇设计
基于PWM调速技术的智能温控风扇设计
基于PWM调速技术的智能温控风扇设计


目    录
摘要    I
Abstract    II
第一章 绪论    1
1.1 引言    1
1.2 本论文主要任务    1
1.3 论文结构安排    2
第二章  系统方案分析与选择论证    3 [版权所有:http://DOC163.com]
2.1 系统概述    3
2.1.1 STC89C52单片机简介    3
2.1.2 本设计基本步骤    3
2.2 系统方案设计    3
2.2.1 温度传感器的选用    3
2.2.2 控制核心的选择    4
2.2.3 显示电路    4
2.2.4 无线遥控    5
2.2.5 调速方式    5
第三章 智能温控风扇系统的硬件设计    7
3.1 总体设计方案框图    7
3.2 单片机主控系统电路设计    7
3.3 控制装置原理    9
3.4 温度显示    9
3.4.1 DS18B20的温度处理方法    9
3.4.2 传感器和显示电路    11
3.5 电机的调速实现方法    11
3.5.1 电机调速原理    11
3.5.2 电机控制模块设计    12
3.6 按键电路    13
3.7 数码管驱动电路    14
3.8 温度显示    14 [资料来源:www.doc163.com]
3.9 红外遥控电路    15
第四章 智能温控风扇的软件设计    16
4.1 软件设计    16
4.1.1 主程序    16
4.1.2 DS18B20测温模块    17
4.2 风扇调速    19
4.3 电机调速与控制子模块    19
第五章 系统调试    21
5.1 用Proteus进行仿真    21
5.2 硬件电路基本调试    22
5.3 分模块调试    22
5.3.1 温控模块的检测调试    22
5.3.2 数码管显示的检测调试    22
5.3.3 红外遥控电路检测调试    23
5.3.4 电机模块检测调试    23
5.4 智能温控风扇硬件演示    24
5.4.1 设置温度上下限值    24
5.4.2 当前温度显示    25
5.4.3 温度值在30℃与33℃之间    25
5.4.4 温度值高于33℃    26
5.4.5 固定档位    26

[资料来源:http://Doc163.com]

5.4.6 红外遥控操作    27
第六章 总结与展望    28
6.1 总结    28
6.2 展望    28
致 谢    29
参考文献    30
附录1 硬件实物图    32
附录2 程序代码    33 [来源:http://Doc163.com]

  • 关于资料
    提供的资料属本站所有,真实可靠,确保下载的内容与网页资料介绍一致.
  • 如何下载
    提供下载链接或发送至您的邮箱,资料可重复发送,若未收到请联系客服.
  • 疑难帮助
    下载后提供一定的帮助,收到资料后若有疑难问题,可联系客服提供帮助.
  • 关于服务
    确保下载的资料和介绍一致,如核实与资料介绍不符,可申请售后.
  • 资料仅供参考和学习交流之用,请勿做其他非法用途,转载必究,如有侵犯您的权利或有损您的利益,请联系本站,经查实我们会立即进行修正! 版权所有,严禁转载
    doc163.com Copyright © 2012-2025 苏ICP备2021029856号-4